| Home > HP Parts Directory > Printers > LaserJet 2200 |
 |
LaserJet 2200 |
| Part # |
Accessories |
| 5063-1256 |
HP Bi-Tronics Parallel Cable (A to B) - DB-25 (M) to 36 Pin Centronics (M) - to Connect to HP Vectra, and IBM PC/AT/XT Compatibles - 2.0m (Replacement for C2950A) |
| 5063-1257 |
HP Bi-Tronics Parallel Cable (A to B) - DB-25 (M) to 36 Pin Centronics (M) - to Connect to HP Vectra, and IBM PC/AT/XT Compatibles - 3.0m (Replacement for C2951A) |
| C2950A |
HP IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
| C2951A |
HP IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
| C4096A |
HP LaserJet 2100 and 2200 Series Toner Cartridge (Ultra Precise Toner) - Prints Approximately 5,000 Pages |
| C4793A |
HP 250 Sheet Universal paper tray assembly (Tray 3) - Holds 250 sheets of letter, legal, Executive, A4, A5, or B5 ISO size paper - Printer sits on top of this tray - Below Tray 2 of P |
| C6518A |
HP Universal Serial Bus (USB) interface cable - Type 'A' connector to type 'B' connector - 1.8m (6.6ft) long |
| C7058-67903 |
HP Duplex feed/Paper pick-up kit - Duplex feed/Paper pick-up kit -Includes duplex feed guide assembly and cassette paper pickup assembly |
| RB2-2935-000CN |
HP Gear Coupler - Between Plate Bushing and Largest Drive Gear |
| RB2-3001-000CN |
HP Paper Cassette - Bare Paper Tray Frame |
| RB2-3036-000CN |
HP Tray 1 Extender - Pullout Tray Extention - Attaches to Flip-out Tray Extender |
| RB2-3037-000CN |
HP Tray 1 extender - Flip-out paper extender |
| RG5-4278-000CN |
HP Sensor Cable - Between Photo Sensor PS2001 and Tray 3 Paper Feeder Drive PC Board - J2110 to J2003 |
| RG5-4280-000CN |
HP Relay Cable - From Feed Drive Controller Board to Feed Drive Relay - One Connector to Two Connectors - Six Wires |
| RG5-4281-000CN |
HP Frame ground cable - Ground connection to feed drive housing - Round crimp lug to push-on connector with green wire |
| RG5-5568-000CN |
HP Cable and Guide Assembly - Cables run between Solenoids and\n Engine Controller Board |
| RG5-5576-000CN |
HP Multi-Purpose Input Tray - Input Tray 1 |
| RG5-5580-000CN |
HP 250 Sheet Paper Tray - Adjusts for Letter, Legal, Exec, A4 - Used for Tray 2 |
| RG5-5583-000CN |
HP Sensor cable - Cable for PS1305 - Paper detection |
| RG5-5598-000CN |
HP Paper-feed Cable - |
| RG5-5623-000CN |
HP 500 Sheet Paper Tray - Adjusts for Letter and A4 |
| RG9-1473-000CN |
HP Coupling Assebly - Engages Drive Gear Assembly |
| RH2-5427-000CN |
HP Flat cable - Connects to laser/scanner assembly |
|
Boards |
| C7066-60001 |
HP Formatter (Main logic) board - For simplex printers only |
| RG5-4277-000CN |
HP Tray 3 Controller Board - Paper Feed Drive PCA |
| RG5-5563-000CN |
HP Power supply board - For 100V-127V operation |
| RG5-5566-000CN |
HP Engine controller board - For 100V-127V operation |
| C4209-69001 |
HP Formatter (Main Logic) Board (Requires Return of defective part) |
|
Chassis/Case |
| RB1-2190-000CN |
HP Pick-up roller spring hook |
| RB1-6133-000CN |
HP Anchor Pin - Anchor Point for Hook Spring |
| RB2-2816-000CN |
HP Rubber Foot - for Bottom of Tray 3 Assembly (4 Used) |
| RB2-2832-000CN |
HP Compression spring - Provides electrical ground connection |
| RB2-2836-000CN |
HP Paper Sensor Lever - Mechanical Device That Engages Photo Sensor PS504 |
| RB2-2837-000CN |
HP Torsion spring - Provides tension for paper sensor lever |
| RB2-2843-000CN |
HP Torsion spring - Provides a small amount of back pressure for the paper sensor flag |
| RB2-2856-000CN |
HP Toner cartridge access door |
| RB2-2943-000CN |
HP Clutch Pin - Holds Drum Drive Clutch Springs - Between Pin Holder and Clutch Spring Plate |
| RB2-2945-000CN |
HP Mount plate - Protective plate for extended I/O PCA |
| RB2-2978-000CN |
HP Compression Spring - Provides Tension for Upper Delivery Rollers Mounted on Upper Delivery Guide - 4 Used |
| RB2-3000-000CN |
HP Front cover - Front cover and pull handle for paper tray |
| RB2-3012-000CN |
HP Leaf Spring - Provides Side Tension for Paper in Tray - Attaches to Right Side Width Adjustment Plate |
| RB2-3041-000CN |
HP Tray hinge - For the left side of the multi-purpose front input tray (tray 1) |
| RB2-3042-000CN |
HP Tray hinge - For the right side of the multi-purpose front input tray (tray 1) |
| RB2-3075-000CN |
HP Leaf spring - Chassis grounding spring |
| RB2-3080-000CN |
HP Grounding plate - Electrical chassis ground connection |
| RB2-3474-000CN |
HP Paper Sensor Lever - Mechanical Link To Photosensor PS2001 |
| RB2-3478-000CN |
HP Leaf spring - Provides tension for drive shaft bushing |
| RB2-3479-000CN |
HP Tray 3 Cover - Covers Bottom of Front Lower Right Corner |
| RB2-3480-000CN |
HP Tray 3 Cover - Covers Bottom of Drive Assembly - Right Side |
| RB2-3481-000CN |
HP Solenoid Plate - |
| RB2-3489-000CN |
HP Tray 3 Cover - Covers Bottom of Front Lower Left Corner |
| RB2-6249-000CN |
HP Feed Guide Hinge - |
| RB2-6271-000CN |
HP Contact spring - High voltage contact for transfer roller |
| RB2-6280-000CN |
HP Top cover asembly - Face-down output tray and toner cartridge access door |
| RB2-6297-000CN |
HP Rubber foot - Mounts on the rear of the middle frame assembly - Printer feet (two used) |
| RB2-6314-000CN |
HP Tension spring - Provides tension for duplexer release knob |
| RB2-6321-000CN |
HP Torsion spring - Provides tension for gear on the paper feed roller and gear for registration assembly |
| RB2-6349-000CN |
HP End Plate - Back End Plate of Paper Cassette |
| RF5-2599-000CN |
HP Lifting Plate - Metal Plate That Supports Paper in Tray |
| RF5-2606-000CN |
HP Adjustable width plate - Right side paper width stop plate |
| RG5-4121-000CN |
HP Multi-Purpose Input Tray Cover Assembly - Tray One Cover - Includes Pull-out and Flip-out Tray Extensions |
| RG5-4159-000CN |
HP Adjustable width plate - Left side paper width stop plate |
| RG5-5545-040CN |
HP DIMM Cover Assembly - Right Side Cover - Includes I/O Cover on Right Rear and Optical Filter Cover on Right Front |
| RG5-5546-000CN |
HP Rear Cover - Back of Printer Cover - Includes Face-down Output Tray Assembly |
| RG5-5549-000CN |
HP Left cover assembly - Includes power button and spring |
| RH7-6051-000CN |
HP Microswitch - Cartridge Access Door Switch - SW1701 |
| RS6-2020-000CN |
HP Plate spring - Provides pressure for paper lifting plate |
| RS6-2021-000CN |
HP Pad spring - Provides tension for separation pad on front of paper tray |
| RS6-2022-000CN |
HP Compression spring - Provides tension for right side of transfer roller bushing |
| RS6-2025-000CN |
HP Tensioning spring - For the paper pick up gear assembly |
| RS6-2030-000CN |
HP Tension spring |
| RS6-2035-000CN |
HP Plate spring - Provides tension for left side width plate |
| RS6-2061-000CN |
HP Clip Spring - Provides Tension for Clip - Attaches to Hook |
| RS6-2062-000CN |
HP Swing gear spring - Provides tension for swing gear assembly |
| RS6-2063-000CN |
HP Roller Spring - Provides Pressure for Tray 3 Feed Roller |
| RS6-2064-000CN |
HP Bushing Spring - Provides Tension for Tray 3 Right Side Feed Roller Support Bushing |
| RS6-2375-000CN |
HP Compression spring - Provides pressure for top output bin delivery roller assembly |
|
Fusers |
| H3978-60001 |
HP Maintenance Kit (120V) - Includes fuser roller assembly, transfer roller assembly, Tray 1 and Tray 2 pick-up rollers, Tray 1 and Tray 2 separation pads. Procedure requires use of service manual. Not for warranty use |
| RG5-5559-110CN |
HP Fusing roller assembly (For 100V to 120V operation) - Bonds toner to paper with heat (Requires Return of defective part.) |
|
Gears & Rollers |
| C7058-67905 |
HP Delivery roller kit - includes all face-down delivery roller assemblies, with upper delivery roller supports and roller drive gear |
| RB2-2849-000CN |
HP Face-Down Delivery Roller - Lower Rollers - Four Used |
| RB2-2891-000CN |
HP Pick-up Roller - Tray 2 and 3 - Black and White Pickup Roller Located near Front Middle of Tray - Slotted Shaft |
| RB2-2892-000CN |
HP Guide Roller - White Plastic Roller - One on Each Side of Rubber Pickup Roller- 2 Used |
| RB2-2893-000CN |
HP Drive shaft - Drives pickup roller |
| RB2-2900-000CN |
HP Pickup roller - MP/TRAY 1 pickup roller |
| RB2-3004-000CN |
HP Release arm - Left side lifting plate release arm |
| RB2-3005-000CN |
HP Release arm - Right side lifting plate release arm |
| RB2-3009-000CN |
HP Lock arm - Locks rear paper length adjustment plate |
| RB2-3010-000CN |
HP Sensor Arm - Paper Sensor Arm - Indicates on Front Cover the Quantity of Paper in Tray |
| RB2-3040-000CN |
HP Gear - 26 tooth - Tray 1 pick-up roller drive gear |
| RB2-3046-000CN |
HP Guide Roller - Provides Pressure Against Pickup Roller - For MP/Tray 1 - Two Used |
| RB2-3073-000CN |
HP Belt drive shaft 1 - Between wide middle belt and the two narrower rear belts - Transfers power from gear assembly |
| RB2-3484-000CN |
HP Feed Roller - Feed Roller for Tray 3 - 2 Used |
| RB2-3490-000CN |
HP Feed Roller - Tray 3 Feed Roller |
| RB2-6268-000CN |
HP Idler Shaft - Small Front Pullies Attached to Small Belts |
| RB2-6269-000CN |
HP Belt drive shaft 2 - Front of middle wide belt - Tiny drive belts attach on each end of this shaft |
| RB2-6270-000CN |
HP Paper feed belt - Short/tiny belts in front of and on each side of middle belt of paper transfer assembly |
| RB2-6272-000CN |
HP Paper feed belt - Wide middle belt |
| RB2-6273-000CN |
HP Paper Feed Belt - Long Narrow Rear Belts - 2 Used |
| RB2-6274-000CN |
HP Belt Shaft 3 - Tiny Idler Shafts at Back of Narrow Paper Belts - 2 Used |
| RB2-6302-000CN |
HP Feed roller - Shaft with two rollers - Feed roller for the paper cassette |
| RB2-6304-000CN |
HP Pick-up Roller - Tray 2 - Roller Located near Front Middle of Tray - Roller has Slotted Shaft |
| RB2-6310-000CN |
HP Paper sensor lever - Senses paper at pickup roller |
| RB2-6318-000CN |
HP Feed Roller - Shaft with two rollers - Feeds paper from the\n duplexer into the registration assembly |
| RB2-6368-000CN |
HP Pressure roller - Applies pressure to paper as it feeds through the fusing roller |
| RB2-6372-000CN |
HP Delivery roller - Feeds paper out of fusing assembly |
| RB2-6374-000CN |
HP Delivery Roller - Roller for Upper Delivery Guide - 4 Used |
| RF5-2755-000CN |
HP Swing gear - Swing assembly includes upper cluster gear |
| RG5-4128-000CN |
HP Multi-purpose tray pick-up roller assembly - Includes pick-up roller, roller cam, right and left cams, both round rollers and dowel pin |
| RG5-4156-000CN |
HP Gear Assembly - Cassette Pick-up Gear Assembly |
| RG5-4391-040CN |
HP Paper Feeder Drive Assembly for Tray 3 |
| RG5-4394-000CN |
HP Feed Roller Assembly - Tray 3 Feed Roller Assembly |
| RG5-5541-000CN |
HP Delivery Roller Assembly - Lower Face-down Output Roller Assembly - Includes Roller and Holder - Used as the Two Outer Edge Roller Assemblies |
| RG5-5542-000CN |
HP Delivery Roller Assembly - Lower Face-down Output Roller Assembly - Includes Roller and Holder - Used as the Two Inner Edge Roller Assemblies |
| RG5-5551-000CN |
HP Cassette paper pickup assembly |
| RG5-5555-000CN |
HP Feed roller assembly - Feed roller for tray 2 |
| RG5-5556-000CN |
HP Registration Assembly - Registration Shutter and Roller\t With Holder Frame Assembly |
| RG5-5560-000CN |
HP Fusing roller assembly (For 100V to 120V operation) - Includes heating element and fixing film sleeve |
| RG5-5562-000CN |
HP Printer Drive Assembly - Gear Assembly on Right Side |
| RG5-5577-000CN |
HP Gear assembly - Drives paper transfer belt assembly |
| RG5-5581-000CN |
HP Transfer roller assembly - Includes left side bushing |
| RG5-5622-000CN |
HP Paper feeder drive assembly for 500 sheet tray |
| RS6-0440-000CN |
HP 10 Tooth Gear - Provides for Coordinated Movement of Width Adjustment Plates |
| RS6-0441-000CN |
HP Drive Gear - Upper Delivery Roller Drive Gear - 15 Tooth |
| RS6-0445-000CN |
HP Gear - 14 Tooth - Drives Registration Roller |
| RS6-0446-000CN |
HP 201 Tooth Gear - Largest Gear in Assembly - Gear #5 |
| RS6-0448-000CN |
HP 17 Tooth/68 Tooth Cluster Gear - Gear #11 |
| RS6-0449-000CN |
HP 25 Tooth/41 Tooth Cluster Gear - Gear #10 |
| RS6-0450-000CN |
HP 31 Tooth Gear - Printer Drive Gear #9 |
| RS6-0451-000CN |
HP 26 Tooth Gear - Printer Drive Gear #8 |
| RS6-0464-000CN |
HP Drive Gear - Engages Feed Belt Gear Assembly - 20 Tooth |
| RS6-0495-000CN |
HP 27 Tooth Gear - Clutch Gear |
| RS6-0497-000CN |
HP 39 Tooth/34 Tooth Cluster Gear - Bottom Gear of Swing Gear A |
| RS6-0498-000CN |
HP 45 Tooth Gear - Largest Gear of Drive Assembly |
| RS6-0499-000CN |
HP 39 Tooth Gear - Connects to Drive Shaft |
| RS6-0500-000CN |
HP 17 Tooth Gear - Smallest Gear in Drive Assembly |
| RS6-0501-000CN |
HP 15 Tooth Drive Gear - Drives Tray 3 Feed Roller |
|
Laser Scanners |
| RG5-5591-000CN |
HP Laser/Scanner Assembly - Mounts on Top of Print Structure |
|
Memory |
| C7842-67901 |
HP 8MB SDRAM - 100MHz synchronous DRAM - DIMM package |
| C7843-67901 |
HP 16MB SDRAM - 100MHz synchronous DRAM - DIMM package |
| C7845-67901 |
HP 32MB SDRAM - 100MHz synchronous DRAM - DIMM Package |
| C7846-67901 |
HP 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
|
Motors & Fans |
| RH7-1458-000CN |
HP Main Motor - Provides Power for Main Printer Drive Assembly |
| RH7-1461-000CN |
HP Reverse Motor - Provides power to turn paper over when it goes through duplexer. |
| RH7-1463-000CN |
HP Cooling fan |
|
Network Devices |
| J3111A |
HP Ethernet 10Base-T/10Base2 and LocalTalk (RJ-45, BNC, LocalTalk) EIO network PCA |
| J4135A |
HP JetDirect connectivity card - Has one USB port, one serial (DB9) port and one LocalTalk port - Plugs in the EIO slot on selected DesignJet and LaserJet printers |
| J3110-69001 |
HP JetDirect 600N EIO internal print server 10Base-T LAN interface board - Has one RJ-45 connector - (J3110A) - Comes Standard in the LaserJet 2100TN (C4172A) |
| J3111-69001 |
HP JetDirect 600N EIO internal print server 10Base-T, 10BASE-2, and LocalTalk LAN interface board - Has one RJ-45, BNC, and 8-pin DIN connector |
| J4169-69001 |
HP Replacement JetDirect 610N Internal Print Server (10Base-T and 100Base-TX) LAN Interface Board - Plugs in Peripherial EIO Slot - Has One RJ-45 Connector (Part of J4169A) |
|
Power Supplies |
| RG5-5565-000CN |
HP Power Receptacle - Power input receptacle and cable going to power supply PCA |
| WD1-0268-000CN |
HP Power Supply Board Fuse - for 110/120V Operation |
|
Miscellaneous |
| 8120-6812 |
HP Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 120V in the USA, Canada, Mexico, Philippines, and Taiwan) |
| RB2-2830-000CN |
HP Cartridge guide - Right side toner cartridge guide |
| RB2-2831-000CN |
HP Cartridge guide - Left side toner cartridge guide |
| RB2-2850-000CN |
HP Roller Bushing - Supports Face-down Upper Delivery Roller |
| RB2-2895-000CN |
HP Shaft bushing/retainer - Pickup Roller Right Side Support Bu |
| RB2-2896-000CN |
HP Shaft bushing/retainer - Pickup Roller Left Side Support Bus |
| RB2-2897-000CN |
HP Shaft bushing/retainer - Right side drive shaft support bush |
| RB2-2926-000CN |
HP Transfer roller bushing - Supports right side of transfer ro |
| RB2-2936-000CN |
HP Coupler bushing - Supports largest drive gear coupler |
| RB2-2944-000CN |
HP PCA guide - Holds extended I/O PC board |
| RB2-2947-000CN |
HP Pin holder - Holds drum drive clutch pin |
| RB2-2950-000CN |
HP Spring spacer - Fits between the two drum clutch springs |
| RB2-2973-000CN |
HP Pressure Roller Support Bushing - 2 Used |
| RB2-3007-000CN |
HP Separation pad - Small rectangular rubber pad on front of metal lifting plate |
| RB2-3013-000CN |
HP Pad holder - Separation pad holder on front of tray |
| RB2-3043-000CN |
HP Left roller bushing - Acts as the bearing and retainer for the left end of the paper pick-up roller assembly (tray 1) |
| RB2-3081-000CN |
HP Feed roller bushing - Right side feed roller support |
| RB2-3475-000CN |
HP Support bushing - Feeder drive shaft bushing |
| RB2-3485-000CN |
HP Roller Holder - Tray 3 Feed Roller Holder - 2 Used |
| RB2-3487-000CN |
HP Roller Bushing - Tray 3 Right Side Feed Roller Bushing |
| RB2-6357-000CN |
HP Entrance guide - Paper input guide to fusing assembly |
| RB2-6470-000CN |
HP Roller Bushing - 500 Sheet Tray Left Side Feed Roller Bushin |
| RB2-6474-000CN |
HP Separation Pad - Small Rectangular Rubber Pad on Front of Cassette arm - Not the one on metal lifting plate |
| RB9-0695-020CN |
HP Separation pad - Moveable pad on front of paper tray |
| RF5-2609-000CN |
HP Contact holder - Anchors fusing assembly to chassis |
| RF5-3272-000CN |
HP Separation pad assembly - Separation pad, holder and spring |
| RF5-3279-000CN |
HP Sensor Lever Holder - |
| RG5-5548-000CN |
HP Reverse guide assembly - Guides paper back into printer to print back side when in duplex mode. |
| RG5-5552-000CN |
HP Duplex solenoid assembly - Solenoid and clutch assembly to engage and disengage duplexer |
| RG5-5553-000CN |
HP Position Guide Assembly - |
| RG5-5554-000CN |
HP Duplex Feed Guide Assembly - Separates paper path from Tray\n 2 when in duplex mode |
| RH7-5213-000CN |
HP Drive solenoid - Engages swing gear assembly |
| RH7-5270-000CN |
HP Solenoid - Tray 2 Pickup Assembly - SL1908 |
| RH7-5273-000CN |
HP Solenoid - Tray 1 Pickup Assembly - SL2908 |
| RH7-5276-000CN |
HP Drive solenoid - Engages swing gear assembly |
| VS1-6174-006CN |
HP Feed Drive Assembly Connector - Electrical Connection Between Tray 3 and Printer |
| WG8-5364-000CN |
HP Photo Sensor - Paper Sensor PS1305 |
| WG8-5382-000CN |
HP Photosensor (PS2001) - Tray 3 Paper Sensor
|
0 items